Gridfinity Extended Generator

This is the model generator for Gridfinity Extended. Any changes you make are saved in the URL, so you can share that URL or create a bookmark to keep those changes around.
For detailed documentation, check the README. Other generators: gridfinity_basic_cup, gridfinity_baseplate, gridfinity_item_holder, gridfinity_drawers, gridfinity_lid, gridfinity_marble, gridfinity_tray, gridfinity_vertical_divider, stanley_basic_cup, gridfinity_baseplate_flsun_q5, gridfinity_chess, gridfinity_glue_stick, gridfinity_sieve, gridfinity_silverware_legacy, gridfinity_silverware, gridfinity_sliding_lid, gridfinity_socket_holder

General Cup

stanley_model
X dimension. grid units (multiples of 42mm) or mm.

width
X dimension. grid units (multiples of 42mm) or mm.

depth
Y dimension. grid units (multiples of 42mm) or mm.

height
Z dimension excluding. grid units (multiples of 7mm) or mm.

filled_in
Fill in solid block (overrides all following options)

wall_thickness
Wall thickness of outer walls. default, height < 8 0.95, height < 16 1.2, height > 16 1.6 (Zack's design is 0.95 mm)

headroom
under size the bin top by this amount to allow for better stacking

Cup Lip

lip_style
Style of the cup lip

lip_side_relief_trigger
Below this the inside of the lip will be reduced for easier access.

lip_top_relief_height
Create a relief in the lip

lip_top_relief_width
how much of the lip to retain on each end

lip_top_notches
add a notch to the lip to prevent sliding.

lip_clip_position
enable lip clip for connection cups

lip_non_blocking
allow stacking when bin is not multiples of 42

height_includes_lip

Subdivisions

chamber_wall_thickness

chamber_wall_headroom
Reduce the wall height by this amount

vertical_chambers
X dimension subdivisions

vertical_separator_bend_position

vertical_separator_bend_angle

vertical_separator_bend_separation

vertical_separator_cut_depth

horizontal_chambers

horizontal_separator_bend_position

horizontal_separator_bend_angle

horizontal_separator_bend_separation

horizontal_separator_cut_depth

vertical_irregular_subdivisions
Enable irregular subdivisions

vertical_separator_config
Separator positions are defined in terms of grid units from the left end

horizontal_irregular_subdivisions
Enable irregular subdivisions

horizontal_separator_config
Separator positions are defined in terms of grid units from the left end

Base

floor_thickness
Minimum thickness above cutouts in base (Zack's design is effectively 1.2)

cavity_floor_radius

flat_base_rounded_radius
Adjust the radius of the rounded flat base. -1 uses the corner radius.

flat_base_rounded_easyPrint
Add chamfer to the rounded bottom corner to make easier to print. -1 add auto 45deg.

Label

label_style

label_position
Include overhang for labeling (and specify left/right/center justification)

label_size
Width, Depth, Height, Radius. Width in Gridfinity units of 42mm, Depth and Height in mm, radius in mm. Width of 0 uses full width. Height of 0 uses Depth, height of -1 uses depth*3/4.

label_relief
Size in mm of relief where appropriate. Width, depth, height, radius

label_walls
wall to enable on, front, back, left, right. 0: disabled; 1: enabled;

Sliding Lid

sliding_lid_enabled

sliding_lid_thickness
0 = wall thickness *2

sliding_lid_min_wall_thickness
0 = wall_thickness/2

sliding_lid_min_support
0 = default_sliding_lid_thickness/2

sliding_lid_clearance

sliding_lid_pull_style

sliding_lid_nub_size

Finger Slide

fingerslide
Include larger corner fillet

fingerslide_radius
Radius of the corner fillet, 0:none, >1: radius in mm, <0 dimention/abs(n) (i.e. -3 is 1/3 the min(width,height))

fingerslide_walls
wall to enable on, front, back, left, right. 0: disabled; 1: enabled using radius; >1: override radius.

fingerslide_lip_aligned
Align the fingerslide with the lip

Tapered Corner

tapered_corner

tapered_corner_size

tapered_setback
Set back of the tapered corner, default is the gridfinity corner radius

Wall Pattern

wallpattern_enabled
Grid wall patter

wallpattern_style
Style of the pattern

wallpattern_strength
Spacing between pattern

wallpattern_walls
wall to enable on, front, back, left, right.

wallpattern_rotate_grid
rotate the grid

wallpattern_cell_size
Size of the hole

wallpattern_dividers_enabled
Add the pattern to the dividers

wallpattern_hole_sides
Number of sides of the hole op

wallpattern_hole_radius
Radius of corners

wallpattern_fill
pattern fill mode

wallpattern_border
border around the wall pattern, default is wall thickness

wallpattern_depth
depth of imprint in mm, 0 = is wall width.

wallpattern_pattern_grid_chamfer
grid pattern hole taper

wallpattern_pattern_voronoi_noise
voronoi pattern noise,

wallpattern_pattern_brick_weight
brick pattern center weight

wallpattern_pattern_quality
$fs for floor pattern, min size face.

Floor Pattern

floorpattern_enabled
enable Grid floor patter

floorpattern_style
Style of the pattern

floorpattern_strength
Spacing between pattern

floorpattern_rotate_grid
rotate the grid

floorpattern_cell_size
Size of the hole

floorpattern_hole_sides
Number of sides of the hole op

floorpattern_hole_radius
Radius of corners

floorpattern_fill
pattern fill mode

floorpattern_border
border around the wall pattern, default is wall thickness

floorpattern_depth
depth of imprint in mm, 0 = is wall width.

floorpattern_pattern_grid_chamfer
grid pattern hole taper

floorpattern_pattern_voronoi_noise
voronoi pattern noise,

floorpattern_pattern_brick_weight
brick pattern center weight

floorpattern_pattern_quality
$fs for floor pattern, min size face.

Wall Cutout

wallcutout_vertical

wallcutout_vertical_position
wall to enable on, front, back, left, right. 0: disabled; Positive: GF units; Negative: ratio length/abs(value)

wallcutout_vertical_width
default will be binwidth/2

wallcutout_vertical_angle

wallcutout_vertical_height
default will be binHeight

wallcutout_vertical_corner_radius

wallcutout_horizontal

wallcutout_horizontal_position
wall to enable on, front, back, left, right. 0: disabled; Positive: GF units; Negative: ratio length/abs(value)

wallcutout_horizontal_width
default will be binwidth/2

wallcutout_horizontal_angle

wallcutout_horizontal_height
default will be binHeight

wallcutout_horizontal_corner_radius

Extendable

extension_x_enabled

extension_x_position

extension_y_enabled

extension_y_position

extension_tabs_enabled

extension_tab_size
Tab size, height, width, thickness, style. width default is height, thickness default is 1.4, style {0,1,2}.

Bottom Text

text_1
Add bin size to bin bottom

text_size
Font Size of text, in mm (0 will auto size)

text_depth
Depth of text, in mm

text_font
Font to use

text_2
Add free-form text line to bin bottom (printing date, serial, etc)

text_2_text
Actual text to add

debug

cut
Slice cup

enable_help
Enable loging of help messages during render.

Model detail

pitch
Work in progress, Modify the default grid size. Will break compatibility

clearance
clearance around the bin, will reduce the bin by this amount in mm.

corner_radius

set_colour
Assign colours to the bin

render_position
Where to render the model

fa
Minimum angle for a fragment (fragments = 360/fa). Low is more fragments

fs
minimum size of a fragment. Low is more fragments

fn
number of fragments, overrides $fa and $fs

random_seed
set random seed for

force_render
force render on costly components

Stanley Pro Shallow

proshallow_size

proshallow_wall_thickenss

proshallow_corner_radius

proshallow_bottom_radius

Stanley Pro Deep

prodeep_size

prodeep_wall_thickenss

prodeep_corner_radius

prodeep_bottom_radius

Stanley FatMax Pro 1-97-519

fatmaxshallow_size

fatmaxshallow_wall_thickenss

fatmaxshallow_corner_radius

fatmaxshallow_bottom_radius

Stanley FatMax Pro Deep 1-97-521

fatmaxdeep_size

fatmaxdeep_wall_thickenss

fatmaxdeep_corner_radius

fatmaxdeep_bottom_radius

Stanley 25-Compartment 1-92-762

compartment25_size

compartment25_wall_thickenss

compartment25_corner_radius

compartment25_bottom_radius

compartment25front_size

compartment25front_wall_thickenss

compartment25front_corner_radius

compartment25front_bottom_radius